Page 2 of 8 FirstFirst 1234 ... LastLast
Results 11 to 20 of 74

Thread: Exhaust that does the 1190 RIGHT

  1. #11
    EBRforum Novice Plotter's Avatar
    Join Date
    Jul 2015
    Location
    Corpus Christi
    Posts
    218
    Dean, is that stainless or titanium? Do you have options? This says slip-on in the description, but the picture above looked like a full system. Please provide more details...

  2. #12
    EBRforum Junkie
    Join Date
    Oct 2012
    Location
    MO
    Posts
    469
    It's stainless and connects to the stock headers, so it's classified as a slip-on. Did this with the power commander. Stock made 160, pc-v was 174. Without motor work, I doubt it will go much over that. I have the full programmable ecm and wideband setup on the way, so I'll be doing my own tuning on it in the following weeks. I believe they (dynojet) targeted 13.5:1 afr. I know for sure the 1125 motor needed a bit more fuel and EBR tuned my RT-3 to 12.8:1 afr and it made more than anything out there aside from the full exhaust system they sold.

    I typically run a couple of weeks out, I think I am at about a 4 week backlog right now.

    Click image for larger version. 

Name:	1190rx-power gain.jpg 
Views:	178 
Size:	45.7 KB 
ID:	440

  3. #13
    EBRforum Novice Plotter's Avatar
    Join Date
    Jul 2015
    Location
    Corpus Christi
    Posts
    218
    Do you have any pictures of the exhaust with the plastics installed? How much of the can shows?

  4. #14
    EBRforum Junkie
    Join Date
    Oct 2012
    Location
    MO
    Posts
    469
    Oddly enough, this is the only one I can find at the moment. It's one of the early test fit pics.

    Click image for larger version. 

Name:	rx-exhaust-test-fit.jpg 
Views:	165 
Size:	282.7 KB 
ID:	444

  5. #15
    EBRforum Novice Plotter's Avatar
    Join Date
    Jul 2015
    Location
    Corpus Christi
    Posts
    218
    If you end up with any photos with a better shot of the bike, please post. Very interested to see.

  6. #16
    EBRforum Junkie
    Join Date
    Oct 2012
    Location
    MO
    Posts
    469
    I'll be putting it back on the bike in the next week for tuning with the programmable ecm and widebands, I'll get one then. It needs a bath in a bad way, so I'll probably wait until that's done. I've gotten caught in several downpours over the last couple of weeks and it hasn't been cleaned off because of those.

  7. #17
    EBRforum Junkie
    Join Date
    Mar 2014
    Location
    Indianapolis
    Posts
    306
    Ordered mine over the weekend. I need more power. . .

  8. #18
    EBRforum Novice Plotter's Avatar
    Join Date
    Jul 2015
    Location
    Corpus Christi
    Posts
    218
    Nice... post some pictures when you get it installed

  9. #19
    EBRforum Novice Plotter's Avatar
    Join Date
    Jul 2015
    Location
    Corpus Christi
    Posts
    218
    Purchased and ready to rock and roll... I just need the ECM from IDSPD now... Looking forward to the exhaust Dean

  10. #20
    EBRforum Junkie
    Join Date
    Mar 2014
    Location
    Indianapolis
    Posts
    306
    Purchased a power commander for Dean's pipe. Still hoping IDSPD does a tune for it.

Similar Threads

  1. Exhaust Mod
    By fabric8 in forum 1190RX
    Replies: 8
    Last Post: 05-21-2015, 09:25 PM
  2. Exhaust tips and tail tidy installed
    By Slowride in forum 1190SX
    Replies: 2
    Last Post: 02-28-2015, 01:40 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •