Page 2 of 4 FirstFirst 1234 LastLast
Results 11 to 20 of 31

Thread: My 1190RX with front end mod

  1. #11
    EBRforum ProvNov
    Join Date
    Jun 2016
    Location
    California
    Posts
    64
    This one a flange to sleeve clamp I made:



    THis one a sleeve adapter I made:


  2. #12
    EBRforum ProvNov ryandcramer's Avatar
    Join Date
    Sep 2016
    Location
    Detroit
    Posts
    56
    Quote Originally Posted by C. Dolan View Post
    I fitted an Akra muffler ( from ebay ) to an HMF mid pipe.

    I have since done others with an Arrow muffler, and just got a Micron TI muffler, today, that weighs under 3 Lbs.

    have you weighed the HMF pipe? I actually have not yet but supppse I could today.

  3. #13
    EBRforum ProvNov ryandcramer's Avatar
    Join Date
    Sep 2016
    Location
    Detroit
    Posts
    56
    Quote Originally Posted by C. Dolan View Post
    I fitted an Akra muffler ( from ebay ) to an HMF mid pipe.

    I have since done others with an Arrow muffler, and just got a Micron TI muffler, today, that weighs under 3 Lbs.

    the inlet is 2.25 inches on the HMF mid pipe? Also, I'm guessing you had the HMf on there? Did you ever weigh the hmf can?
    Last edited by ryandcramer; 04-14-2017 at 11:57 AM.

  4. #14
    EBRforum Junkie
    Join Date
    Jul 2015
    Location
    on a curvey road, by a drag strip
    Posts
    472
    Quote Originally Posted by ryandcramer View Post
    the inlet is 2.25 inches on the HMF mid pipe? Also, I'm guessing you had the HMf on there? Did you ever weigh the hmf can?
    Yes it is 2.25" o.d. and the outlet is1.875"

  5. #15
    EBRforum ProvNov
    Join Date
    Jun 2016
    Location
    California
    Posts
    64
    Quote Originally Posted by ryandcramer View Post
    the inlet is 2.25 inches on the HMF mid pipe? Also, I'm guessing you had the HMf on there?

    Did you ever weigh the hmf can?
    5 Lbs. for the HMF can

    3 Lbs Akra

    Somewhere between 2 1/2 to 3 Lbs on the Micron

  6. #16
    EBRforum ProvNov ryandcramer's Avatar
    Join Date
    Sep 2016
    Location
    Detroit
    Posts
    56
    Quote Originally Posted by C. Dolan View Post
    5 Lbs. for the HMF can

    3 Lbs Akra

    Somewhere between 2 1/2 to 3 Lbs on the Micron
    really? I was told 7-9 by HmF! Hmm, I'm going to fit the hotbodies MFP growler and see how it runs compared to the hmf and ecm 44T HMF ECM. if it runs terrible I'm switching the ecm to the tunable ecm and get the power back to "normal". The HB can weighs just over 2lbs.

  7. #17
    EBRforum ProvNov ryandcramer's Avatar
    Join Date
    Sep 2016
    Location
    Detroit
    Posts
    56
    My HMF can that was cut 4" weighs 5.15 lbs

    the hot bodies MGP carbon can weighs 1.75

    ordered the can and will retro fit and then dyno tune it.

    This is with the rear wheel and rotor mod should take another 10.5-11lbs and then I'm going after the engine bolts

  8. #18
    EBRforum Junkie
    Join Date
    Jul 2015
    Location
    on a curvey road, by a drag strip
    Posts
    472
    Quote Originally Posted by ryandcramer View Post
    My HMF can that was cut 4" weighs 5.15 lbs

    the hot bodies MGP carbon can weighs 1.75

    ordered the can and will retro fit and then dyno tune it.

    This is with the rear wheel and rotor mod should take another 10.5-11lbs and then I'm going after the engine bolts
    Do you have a good dyno tuner down in the Detroit area or are you taking the bike over to IDS in Decatur?

  9. #19
    EBRforum ProvNov ryandcramer's Avatar
    Join Date
    Sep 2016
    Location
    Detroit
    Posts
    56
    Quote Originally Posted by buell-fan View Post
    Do you have a good dyno tuner down in the Detroit area or are you taking the bike over to IDS in Decatur?
    Apex Manufacturing will do the dyno. Harry is damn good and they did the front end work. I trust them. They are in Clinton, Michigan near Ann Arbor.

  10. #20
    EBRforum Newb
    Join Date
    Aug 2015
    Location
    Detroit
    Posts
    15
    Apex isn't too far from me. I didn't know they did Dyno tuning...

Similar Threads

  1. 1190rx complete front end for sale: make offer
    By ryandcramer in forum EBR / Buell Wanted or For Sale -- Parts
    Replies: 2
    Last Post: 11-19-2016, 08:45 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •