View Full Version : Aftermarket parts lists
MakingPAIN
07-21-2017, 11:13 AM
i have been looking around for parts suppliers and i thought it would be a good idea for everyone to get together and post up any manufactures/suppliers they can think of that currently sells EBR parts
-Hotbodies racing= race body work
-R@G= frame sliders, grills for coolers, small tidbits
-5-0dro= swing arm and fork protection
-Driven racing= spools
-Dean Adams= EBR exhaust/ special tools/ Buell exhaust
-APH= exhaust
-IDSPD= ECM (Dean Adams-APH-HMF-Muffler delete-programmable)
-STITCH WILSON =seats stitch@customcycleseats.com
-Diesel moto= rotors
-Vortex= aluminum sprockets part #Vortex-821-43(43 tooth) and pegs
-Amsoil= you know why
-HMF= exhaust
-EBC= brake pads
-HIFLO= oil filters
-Knight Design= lower foot pegs
-AF1= store front for parts
-Bestem USA= carbon body work
-ABM=Clutch levers and brake levers
-GB Racing= crash protection for engine cases
-Motion Pro= throttle set up and cables
-Wilbers= shocks
-Showa= shocks
-PowerBronze= seat cowl, tire hugger
-Twisted Design= tidy tail kit
-ASV= levers
-quickshifter (no manufacture)= FUN
-T-Rex= frame sliders/ case protection
-JT Sprocket=JT Sprockets JTR1490.43 - steel
-wave rotor=BL02FID
-Ohlins- steering damper(model#SD000) bushing kit# a14010200ux0631
-K&N= oil filter part # KN-564
-Screensforbikes.com= 1190rx wind screens tall and short.
-keyless gas cap= post 38 on this thread for link (EBRRider)
-Updated chain slider= part #G0012.1B7A
-Barnett= clutch springs frictions and steels... look up Buell 1125 parts
-NCCR= online store front for parts. Has OEM and aftermarket parts
-Spark plug= NGK Spark Plug CR9EKB
-metal mesh oil filter=http://kandpengineering.com/product-catalog/s27/
- Supersprox= sprocket kits
-BuellTooth= quick shifter and dongle
-St Paul harley= random parts EBR and Buell
CRG - RC2 Brake and Clutch levers for 2005 zx6r Part # 2RN-511-T-B
Techspec - Tank Pads
Liquid Performance eBay page - LAP's online discount part sales
Öhlins - BU-888 is the 1125/RS rear shock, a drop-in part to the 1190RX/SX, a note though: these were all built in 2011 or earlier. If you purchase one, you'll have to have it serviced/rebuilt before you fit it to your bike or the seals will fail very quickly.
Woodcraft - replacement/upgraded clip ons, replacement solid foot pegs, hand guards
Shorai - Makers of the battery, battery cable, battery charger
McMaster-Carr for Washers and O-Rings
M18 Oil Drain Plug LH Washer - Equivalent to EBCF0092.1B6 - https://www.mcmaster.com/#97725a860/=1bnm6de
M12 Oil Drain Plug RH Washer - Equivalent to EBCF0091.1B6 - https://www.mcmaster.com/#97725a250/=1bnm6vb
Oil Filter Cover O-Ring - Equivalent to EBCF0003.1B6 - https://www.mcmaster.com/#9452k147/=1bnm7hx
gdisaac07 hooked this list up... i will stay in touch with him for links and such.. thanks bud for the clean up
OEM Parts Supply
EBR Parts Supply - http://www.erikbuellracing.net/store/
Updated chain slider (Part # G0012.1B7A)
LAP eBay page, Liquid Performance - https://www.ebay.com/sch/liquid_performance/
Aftermarket Dealers
AF1 (Our Forum Sponsor) -
NCCR (Official European EBR parts supplier, plus other aftermarket parts) -
St. Paul Harley Davidson - https://sphdonline.com/
Bodywork
Bestem USA
Carbon fiber replacement parts -
Hotbodies Racing
Full race fiberglass bodywork - https://www.hotbodiesracing.com/prod...race-bodywork/ (https://www.hotbodiesracing.com/product/1190rx-2014-15-race-bodywork/)
PowerBronze
Seat cowl and tire hugger -
Screensforbikes.com
1190RX windscreen, short and tall -
Slingshot Racing
Keyless Billet Gas Cap - https://www.slingshotracing.net/cata...cap-p-868.html (https://www.slingshotracing.net/catalog/buell-1125xb9xb12-ebr-1190rs1190rx-keyless-race-gas-fuel-cap-p-868.html)
Twisted Designs
Tail Tidy Kit -
Seat
Stitch Wilson
Custom seats - stitch@customcycleseats.com
Rider InterfaceABM
Clutch Lever (Part # ) -
Brake Lever (Part # ) -
ASV
Clutch Lever (Part # ) -
Brake Lever (Part # ) -
CRG
Clutch Lever (RC2 for 2008 Kawasaki ZX-14, Part # , Shorty and other colors available too) -
Brake Lever (RC2 for 2005 Kawasaki ZX-6R, Part # 2RN-511-T-B, Shorty and other colors available too) -
Knight Design
Pegs
Motion Pro
Adjustable throttle (Rev 2.1 Throttle tube, Part # ) -
Vortex
Pegs -
Woodcraft
Clip ons/bars (Part # ) -
Solid foot pegs (Part # ) -
Hand guards(Part # ) -
Protection
5-0Dro
Swingarm and fork protection -
GB Racing
Engine Case Protection -
R&G
Frame sliders, cooler grills, assorted tidbits -
T-Rex
Frame sliders, engine sliders, axle slider
Techspec
Tank Pads (Part # ) -
Exhaust
APH
Exhaust -
Dean Adams
Round can or oval can exhaust, including ECU (either the one with the map exclusively for the type you buy, or a tunable ECU) -
Various other tools -
HMF
Exhaust -
Engine
Barnett
Clutch springs (Part # , required if you're using a new exhausting and putting down more power than stock) -
Clutch packs (Part # , this is the 1125 carbon fiber clutch pack) -
L.A. Sleeve
Upgraded cylinder sleeves
NGK
Spark Plug (Part # CR9EKB) -
Electronics
BUELLTooth
Quickshifter, regular shift pattern -
Quickshifter, GP shift pattern -
IDS
Original designer of the ECU, sells ECU's with other tunes, plus a user-tunable one -
Shorai
OEM Lithium Battery (Part # LFX21A7-BS17) -
Battery Charger (Part # SHO-BMS01) -
Battery Cable (Part # ) -
Woodcraft
Ignition bypass (Part # ) -
Sprockets
JT Sprocket
Steel, 43 tooth, Part # JTR1490.43 -
Steel, 44 tooth, Part # JTR1490.44 -
Supersprox
Steel/Aluminum engineered sprockets -
Vortex
Aluminum, 43 tooth, Part # Vortex-821-43 -
Aluminum, 44 tooth, Part # Vortex-821-44 -
Suspension
Öhlins
Front Fork Cartridge Kit (Call Seacoast Sport Cycle for NIX30 kit, installed for $1,750 + Shipping) -
Rear Shock (Part # BU-888 is the 1125/RS rear shock, a drop-in part to the 1190RX/SX. A note though: these were all built in 2011 or earlier. If you purchase one, you'll have to have it serviced/rebuilt before you fit it to your bike or the seals may fail very quickly) -
Steering Damper (Part # SD000, requires bushing kit Part # A14010200UX0631) -
Showa
Stock Big Piston Forks and Shock -
Race Shock -
Wilbers
Race Shock -
Brakes
Diesel Moto
Front Rotor -
EBC
Brake Pads -
SBS
Dual Sinter Front Brake Pads (Part # 856DS) -
Wave Rotor
Front Rotor, Part # BL02FID
Fluids and Filters
YOU MUST USE 10W-40 SYNTHETIC ENGINE OIL IF YOU PLAN ON RIDING AT ANY TIME WHEN IT IS LESS THAN 40 DEGREES FAHRENHEIT. OTHERWISE, USE 20W-50 SYNTHETIC.
AMSOIL (EBR recommends that you use AMSOIL)
10W-40 Oil (Part # MCF+QT-EA) -
20W-50 Oil (Part # MCVQT-EA) -
HIFLO
Oil Filter (Part # ) -
K&N
Oil Filter (Part # KN-564) -
K&P Engineering
Metal mesh oil filter (Part # ) - http://kandpengineering.com/product-catalog/s27/
McMaster-Carr
M18 Oil Drain Plug LH Washer - Equivalent to EBCF0092.1B6 - https://www.mcmaster.com/#97725a860/=1bnm6de
M12 Oil Drain Plug RH Washer - Equivalent to EBCF0091.1B6 - https://www.mcmaster.com/#97725a250/=1bnm6vb
Oil Filter Cover O-Ring - Equivalent to EBCF0003.1B6 - https://www.mcmaster.com/#9452k147/=1bnm7hx
Mobil 1
10W-40 Oil -
20W-50 Oil -
Royal Purple
10W-40 Oil -
20W-50 Oil -
Spools/Stands/Restraints
Driven Racing
Spools -
Pit Bull
Spools (6mm, Delrin only) -
Rear pit stand (Wide stand) -
Front pit headlift stand (Pin #1) -
Trailer Restraint System (Part # ) -
i will try to keep the list up to date
please help out with it if you can thanks....
Hughlysses
07-21-2017, 11:50 AM
Knight Design makes the footpegs that were used on the Black Lightning prototypes:
1" drop foot pegs, black, Sidetrax tread for Buell Black Lightning
PN# 101410-1110 $129.99 a pair, 1" drop compared to stock pegs.
http://www.knightdesignllc.com/index.htm
oddball
07-21-2017, 02:29 PM
Looks like our lead BASTARD is on the job. :smirk:
MakingPAIN
07-21-2017, 02:33 PM
Lmao that was a good one right there!!!:lol2:
Nemesis
07-22-2017, 12:00 AM
Cheers for the list :301:
Cooter
07-23-2017, 01:19 PM
Oh lord.... haha
EBRRider
07-23-2017, 04:09 PM
So i have been looking around for parts suppliers and i thought it would be a good idea for everyone to get together and post up everyone they can think of that currently sells EBR parts
-Hotbodies racing= race body work
-R@G= frame sliders, grills for coolers, small tidbits
-5-0dro= swing arm and fork protection
-Driven racing= spools
-Dean Adams= exhaust
-APH= exhaust
-IDSPD= ECM
-sTITCH WILSON =seats
-Diesel moto= rotors
-Vortex= sprockets and pegs
-Amsoil= you know why
-HMF= exhaust
-EBC= brake pads
-HIFLO= oil filters
-Knight Design= lower foot pegs
-Bestem USA= carbon body work
-ABM=Clutch and brake levers
-GB Racing= crash protection for engine cases
-Motion Pro= throttle set up and cables
-Wilbers= shocks
-Showa= shocks
-PowerBronze= seat cowl, tire hugger
-Twisted Design= tidy tail kit
i will try to keep the list up to date
please help out with it if you can thanks....
ASV Shorty = levers
Quick shifter = FUN !
Stitch
07-24-2017, 08:58 AM
Damn, I already made the list! Thanks :) my site is customcycleseats.com, for those folks not on fb.
MakingPAIN
07-24-2017, 09:26 AM
Stitch your the most important supplier!!!!!! you keep our azz on our bikes, no one likes a raw butt after riding :bannana:
yzf29
07-24-2017, 09:55 AM
Thanks for putting this list together!
Davem3racer
07-24-2017, 09:27 PM
T-Rex Racing - Frame sliders and engine case covers
LSL - X-Bar Handlebars for the SX
Thanks for putting this together all in one place.
EBRRider
07-25-2017, 01:24 PM
JT & Vortex rear sprockets
MakingPAIN
07-25-2017, 03:29 PM
Couldn't find a JT sprocket for us
EBRRider
07-25-2017, 03:54 PM
http://ebrforum.com/showthread.php?1410-Steel-rear-sprocket (https://www.amazon.com/gp/product/B001AVS70I/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1)
https://www.amazon.com/gp/product/B001AVS70I/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
15841585
EBRRider
07-25-2017, 05:55 PM
Braking Wave Rotor Manufacturer Part Number: BL02FID
MakingPAIN
07-25-2017, 08:53 PM
When I put our type of bike in the little tab guy on Amazon it says it doesn't fit. Have you personally tried them out and they work alright.
MakingPAIN
07-25-2017, 09:54 PM
1586
Is this the one your talking about because I get a couple different rotors when I search it
Found it on the E bay can't find if it is the same width? I think our rotors are a little different like 5mm and the old ones are 6mm. And the new ones are vented but that's not a biggie. Help me out the width thing?
MakingPAIN
07-25-2017, 10:06 PM
http://ebrforum.com/showthread.php?1410-Steel-rear-sprocket (https://www.amazon.com/gp/product/B001AVS70I/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1)
https://www.amazon.com/gp/product/B001AVS70I/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
15841585
In the thread he said the I.D was 120 of the sprocket and hub O.D was 117. I see it has worked for him and you but I was always under the notion that those were supposed to be a interference fit??? The bolts or studs just lock the chain wheel to the rim, and all centering is done with that hub to sprocket fit. I could be wrong
Cooter
07-25-2017, 10:18 PM
The front brake rotors are the same for XB, 1125 and 1190's. 5mm or 6mm won't matter. Just get your preference.
The stock rear sprocket is hub centric at 117mm but certainly not an 'interference fit'. The slightly bigger hub diameter on the steel JT sprocket shouldn't make any difference. IMO, I'd put a small (1-1.5mm) o-ring on the hub to center it and torque to spec. If one comes out with a 117mm hub I'd buy it, but for now the 120mm works just fine on my SX.
MakingPAIN
07-25-2017, 10:32 PM
The front brake rotors are the same for XB, 1125 and 1190's. 5mm or 6mm won't matter. Just get your preference.
The stock rear sprocket is hub centric at 117mm but certainly not an 'interference fit'. The slightly bigger hub diameter on the steel JT sprocket shouldn't make any difference. IMO, I'd put a small (1-1.5mm) o-ring on the hub to center it and torque to spec. If one comes out with a 117mm hub I'd buy it, but for now the 120mm works just fine on my SX.
Yeah I figured the small different in 5mm to 6mm wouldn't seize the rotor but just had to throw it out there. So use a xb rotor on ebr if you can't find a oem one.
You know what I ment by "interference" as in mesh, snug. All my other bikes sprockets fit nice. Haven't had one all sloppy and just snug my bolts down and call it a day is all I am saying. Not saying all bikes are this way, but if it works it works. Good to know. I will throw it up
MakingPAIN
07-25-2017, 10:59 PM
Can anyone find clutch plates or parts ? Other than the easy pull kit. And if you know where the ez pull kit is that would be cool. Seems like it was only through EBR
EBRRider
07-26-2017, 08:04 AM
1586
Is this the one your talking about because I get a couple different rotors when I search it
Found it on the E bay can't find if it is the same width? I think our rotors are a little different like 5mm and the old ones are 6mm. And the new ones are vented but that's not a biggie. Help me out the width thing?
Yes. thats the one. 1587
EBRRider
07-26-2017, 08:08 AM
(https://www.amazon.com/gp/product/B001AVS70I/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1)http://ebrforum.com/showthread.php?1410-Steel-rear-sprocket
https://www.amazon.com/gp/product/B001AVS70I/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
15841585
-JT Sprocket=JT Sprockets JTR1490.43, You might note its is made of Steel.
MakingPAIN
07-26-2017, 08:57 AM
got it, thanks EBRRider and everyone for the help so far
EBRRider
07-26-2017, 09:06 AM
and the Vortex sprocket . , is a good list for all.
MakingPAIN
07-26-2017, 09:08 AM
and the Vortex sprocket . , is a good list for all.
got the vortex in there "-Vortex= aluminum sprockets and pegs"
you got a part number on hand you would like up there?
EBRRider
07-26-2017, 09:34 AM
got the vortex in there "-Vortex= aluminum sprockets and pegs"
you got a part number on hand you would like up there?
http://www.ebay.com/itm/291942186506?redirect=mobile Its what I am running now. 43 t
EBRRider
07-26-2017, 10:42 AM
How about ECMs Race from IDS , with Deans tune and secondary delete ?
MakingPAIN
07-26-2017, 10:48 AM
yeah i put their company as a whole up so a potential buyer could go to their site and find what they are looking for... i could put up what they supply for tunes..
EBRRider
07-26-2017, 10:50 AM
yeah i put their company as a whole up so a potential buyer could go to their site and find what they are looking for... i could put up what they supply for tunes..
Sorry I see it .
MakingPAIN
07-26-2017, 10:51 AM
i threw up the tunes they provide good thinking
EBRRider
07-26-2017, 11:27 AM
Most all of us know most of this , but for newbes WOW what a great list of resources,
MakingPAIN
07-26-2017, 11:30 AM
That's what I was thinking too. Help out the new peepz... Thanks again for helping out man
https://www.amazon.com/gp/product/B00K803WHU/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
https://www.amazon.com/Ohlins-SD-000-Steering-Damper/dp/B0067F630I/ref=sr_1_1?ie=UTF8&qid=1501087301&sr=8-1&keywords=ohlins+sd+000
Parts for upgrading to Ohlins Steering damper if you feel the need to have an adjustable steering damper. You only need one of the small sleeves to make it fit. Basically one of the holes on the damper is to large for the stock mounting hardware. Just press the sleeve into the hole and you are all set. I was able to do the press work with a set on channel locks.
EBRRider
07-26-2017, 12:08 PM
https://www.amazon.com/gp/product/B004QSDDVU/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
K&N oil filters
Cooter
07-26-2017, 04:35 PM
I really really want an adjustable damper....
It was getting a little unsettled mid-corner so I took mine off to see if it was really working. It is, but the valving is very, very, light.
MakingPAIN
07-26-2017, 06:02 PM
I really really want an adjustable damper....
When I seen it I said the same thing
EBRRider
07-26-2017, 09:51 PM
Keyless Billet Aluminum Quick Release Race CNC Gas Fuel Petrol Cap (For) EBR 1190RS 1190RX BUELL 1125 XB9 XB12 (https://www.amazon.com/Keyless-Billet-Aluminum-Release-Petrol/dp/B00K3745I8/ref=sr_1_8?ie=UTF8&qid=1501123779&sr=8-8&keywords=ebr+1190rx)
MakingPAIN
07-27-2017, 09:23 AM
Bastards join forces for a list of goodies for our Bastard bikes... how sweet :cheers:
EBRRider
07-27-2017, 09:40 AM
I sure like my CRG Hindsight Lanesplitter Bar End Mirror
https://www.revzilla.com/motorcycle/crg-hindsight-lanesplitter-bar-end-mirror
muleman
07-28-2017, 03:30 AM
Clutch friction plates?
MakingPAIN
07-28-2017, 07:48 AM
Clutch friction plates?
Yeah if you can find them let me know. I think they might run 1125 frictions but I am not sure ?
Stitch
07-29-2017, 10:27 AM
Any chance you could stick my info in next to my name in the first post? stitch@customcycleseats.com thanks :)
MakingPAIN
07-31-2017, 09:24 AM
Got you stitch.
zviadi
07-31-2017, 02:59 PM
Fit clutch kit Barnett from 1125.
http://ebrforum.com/showthread.php?1374-Parts-crossover-list
MakingPAIN
08-14-2017, 10:08 AM
https://www.amazon.com/gp/product/B00K803WHU/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
https://www.amazon.com/Ohlins-SD-000-Steering-Damper/dp/B0067F630I/ref=sr_1_1?ie=UTF8&qid=1501087301&sr=8-1&keywords=ohlins+sd+000
Parts for upgrading to Ohlins Steering damper if you feel the need to have an adjustable steering damper. You only need one of the small sleeves to make it fit. Basically one of the holes on the damper is to large for the stock mounting hardware. Just press the sleeve into the hole and you are all set. I was able to do the press work with a set on channel locks.
got it, good catch
Kid Thunder
08-14-2017, 10:55 AM
Thanks! Don't want anyone to mess up the eye in the damper. I had just enough brains to not mess it up! lololol
MakingPAIN
08-25-2017, 02:29 PM
Any one have a air filter or spark plug number to post up ?
EBRRider
08-25-2017, 04:26 PM
http://ebutik.nccr.se/ebr-erik-buell-racing-1/ebr-oem-original-parts/ebr-engine/air-filter
MakingPAIN
08-25-2017, 05:02 PM
I threw up the whole site. I always forget about them
EBRRider
08-25-2017, 05:47 PM
NGK Spark Plug CR9EKB
NGK Spark Plug CR9EKB For '11-'17 RSV4 (all variants), and '11-'17 Tuono V4 (all variants) Also for EBR 1190 RX
https://www.af1racing.com/store/Scripts/prodList.asp?idCategory=2846
https://www.af1racing.com/store/Scripts/prodList.asp?idCategory=2844 (https://www.af1racing.com/store/Scripts/prodList.asp?idCategory=2846)
Hughlysses
08-28-2017, 05:34 AM
I saw a post on Facebook over the weekend that an O-ring for a Ford Focus water pump is a perfect match for the fuel pump O-ring for Buell XB's, which I'd guess is the same as the 1190's.
1678
I'd have some concern about material compatibility, but if the size is right, it'd certainly work in a pinch.
Edit- I checked the material and it's Nitrile, which is OK for gasoline. It will swell 5-10% over time, but shouldn't break down.
buell-fan
08-28-2017, 07:19 AM
Cleanable/reusable metal mesh oil filter. I run them in all my bikes. Super flow and they let you know if you have any issues with the motor when you clean them. Well worth the money if you change oil often like I do. It saved me a lot of motor repair once when I found needle bearing particles in the filter.
http://kandpengineering.com/product-catalog/s27/
MakingPAIN
09-01-2017, 07:17 PM
Cleanable/reusable metal mesh oil filter. I run them in all my bikes. Super flow and they let you know if you have any issues with the motor when you clean them. Well worth the money if you change oil often like I do. It saved me a lot of motor repair once when I found needle bearing particles in the filter.
http://kandpengineering.com/product-catalog/s27/
The bearing material you found in your filter, did you find where it came from?
Quick shifters from NCCR - i received mine from his first production and i couldnt tell the difference between his and the one that i got from EBR last year. They did a great job taking over the production of these. They also found some cost savings during production and passed that on to the consumer - they gave me a $30 credit after i recieved the parts. When is the last time that you had that happen? Great people to work with and they are in stock now.
http://ebutik.nccr.se/ebr-erik-buell-racing-1/ebr-oem-original-parts/ebr-controls/ebr-1190-quick-shift-kit-standard-shift-pattern
http://ebutik.nccr.se/ebr-erik-buell-racing-1/ebr-oem-original-parts/ebr-controls/ebr-1190-quick-shift-kit-gp-shift-pattern
EBRRider
09-02-2017, 08:37 AM
Quick shifters from NCCR - i received mine from his first production and i couldnt tell the difference between his and the one that i got from EBR last year. They did a great job taking over the production of these. They also found some cost savings during production and passed that on to the consumer - they gave me a $30 credit after i recieved the parts. When is the last time that you had that happen? Great people to work with and they are in stock now.
http://ebutik.nccr.se/ebr-erik-buell-racing-1/ebr-oem-original-parts/ebr-controls/ebr-1190-quick-shift-kit-standard-shift-pattern
http://ebutik.nccr.se/ebr-erik-buell-racing-1/ebr-oem-original-parts/ebr-controls/ebr-1190-quick-shift-kit-gp-shift-pattern
4590 Swedish Kronas or 4590 SEK to USD: = 573,77 US Dollars
Click "VAT excluded" - it goes down to $459.00
Nemesis
09-02-2017, 11:07 AM
4590 Swedish Kronas or 4590 SEK to USD: = 573,77 US Dollars
Bargain. Still cheaper than most ebr parts lol.
Kid Thunder
09-02-2017, 06:13 PM
No down shift though, huh?
EBRRider
09-02-2017, 06:19 PM
No down shift though, huh?
Nope , Just gotta do a little Blipping for down shifting without the clutch.
Kid Thunder
09-02-2017, 10:33 PM
Yeah, that's what I do now.
MakingPAIN
09-20-2017, 12:00 PM
supersprox now makes sprockets for us
EBRRider
09-20-2017, 01:04 PM
Front sprockets or just rears ?
MakingPAIN
09-20-2017, 01:26 PM
Just rears from what I could find. Let me know if you see fronts
Hughlysses
09-20-2017, 07:32 PM
supersprox now makes sprockets for us
I saw this posted on Facebook earlier this week. Guy said they came up with rear sprocket quickly after he requested one, and he is talking to them about developing a front sprocket.
MakingPAIN
09-20-2017, 08:19 PM
I saw this posted on Facebook earlier this week. Guy said they came up with rear sprocket quickly after he requested one, and he is talking to them about developing a front sprocket.
Nice I wouldn't even mind the front aftermarket sprocket used the rubber dampers still
Kid Thunder
09-20-2017, 09:52 PM
$146!! Supersprox Stealth rear. A little pricey. I paid less than $100 for my Tuono rear.
Nemesis
09-21-2017, 12:40 AM
$146!! Supersprox Stealth rear. A little pricey. I paid less than $100 for my Tuono rear.
More expensive than from ebr!
What are the benefits of theirs????
Hughlysses
09-21-2017, 08:30 AM
More expensive than from ebr!
What are the benefits of theirs????
It uses a steel-toothed section mounted on an aluminum carrier. 3 times the life of an aluminum sprocket but much less weight than an all-steel sprocket.
MakingPAIN
09-21-2017, 09:04 AM
If the price reflects the quality I am good with it.
Kid Thunder
09-21-2017, 12:41 PM
It is a great sprocket, don't get me wrong. light & strong. Been running them on my 03 Tuono for years. But the price for the EBR one is high.
Hughlysses
09-21-2017, 09:34 PM
Update on front sprocket from Supersprox, posted to the EBR 1190 Owners Group on Facebook by Dallas Beranek:
Sooooooo great news everyone..... I've been in contact with supersprox in regards to our front and rear sprocket problems. They've already made a file and part number for our rear sprockets in any tooth you want (41-47) in their stealth model that is an aluminum center and steel teeth hybrid thats is decently priced for the quality and longevity of the product. So now here's the reason I'm making a second post about this....... They've agreed to making a replacement for our front sprocket that will have a replaceable "consumable" sprocket that bolts to a machined piece that replaces our unit. The only catch is that we will have to do a group buy of 50 units to start to make the necessary tooling and machining processes. This is a feeler post to see if we have 50 people interested enough and then they will be giving me a price soon. I told him that if they were priced close to $200 and replacement sprockets $40-$50 that I think it shouldn't be a problem.
if you're on FB, post up and let him know if you're interested.
MakingPAIN
09-21-2017, 09:57 PM
No facebook but put one down for me if it comes down to it.
No facebook but put one down for me if it comes down to it.
same here
Slickit
12-18-2017, 01:24 AM
Can we change the info for the Ohlins steering damper, specifically the bushing kit. Instead of the a14010200ux0631 number, can we put “Oilless Bearing Sleeves Composite Bushing 6mm x 8mm x 8mm” instead?
Cooter
12-18-2017, 03:59 PM
It's already in a rod end. Any 6mm to 8mm sleeve material will do. Aluminum is fine.
I see you list Buelltooth as a dongle for EBR. Isn't the baud rate different? Does the diagnostic function and ECM parameters work? I don't believe there's any tuning options (yet).
Kid Thunder
12-30-2017, 06:20 PM
NGK CR9EIX Iridium. Got them on line for $1 more than standard.
phelan
12-31-2017, 05:39 PM
They only have quick shifters for EBRs to my knowledge. There are no aftermarket tuning options for EBRs. The only option is an IDS programmable ECM, sold through IDS or EBR.
Kid Thunder
12-31-2017, 11:57 PM
Not sure what you are answering but Buelltooth sells one as well as NCCR out of Sweden. The Buelltooth is cheapest & looks good. I have one but haven't installed it yet.
gdisaac07
02-20-2018, 12:20 PM
Things to add to the list:
CRG - RC2 Clutch lever for 2008 Kawasaki ZX14
EDIT: RC2 Brake lever for 2005 Kawasaki ZX-6R
Techspec - Tank Pads
Liquid Performance eBay page - LAP's online discount part sales
Öhlins - BU-888 is the 1125/RS rear shock, a drop-in part to the 1190RX/SX, a note though: these were all built in 2011 or earlier. If you purchase one, you'll have to have it serviced/rebuilt before you fit it to your bike or the seals will fail very quickly.
Woodcraft - replacement/upgraded clip ons, replacement solid foot pegs, hand guards
Shorai - Makers of the battery, battery cable, battery charger
McMaster-Carr for Washers and O-Rings
M18 Oil Drain Plug LH Washer - Equivalent to EBCF0092.1B6 - https://www.mcmaster.com/#97725a860/=1bnm6de
M12 Oil Drain Plug RH Washer - Equivalent to EBCF0091.1B6 - https://www.mcmaster.com/#97725a250/=1bnm6vb
Oil Filter Cover O-Ring - Equivalent to EBCF0003.1B6 - https://www.mcmaster.com/#9452k147/=1bnm7hx
MakingPAIN
03-05-2018, 01:04 PM
Things to add to the list:
CRG - RC2 Brake and Clutch levers for 2008 Kawasaki ZX14
Techspec - Tank Pads
Liquid Performance eBay page - LAP's online discount part sales
Öhlins - BU-888 is the 1125/RS rear shock, a drop-in part to the 1190RX/SX, a note though: these were all built in 2011 or earlier. If you purchase one, you'll have to have it serviced/rebuilt before you fit it to your bike or the seals will fail very quickly.
Woodcraft - replacement/upgraded clip ons, replacement solid foot pegs, hand guards
Shorai - Makers of the battery, battery cable, battery charger
McMaster-Carr for Washers and O-Rings
M18 Oil Drain Plug LH Washer - Equivalent to EBCF0092.1B6 - https://www.mcmaster.com/#97725a860/=1bnm6de
M12 Oil Drain Plug RH Washer - Equivalent to EBCF0091.1B6 - https://www.mcmaster.com/#97725a250/=1bnm6vb
Oil Filter Cover O-Ring - Equivalent to EBCF0003.1B6 - https://www.mcmaster.com/#9452k147/=1bnm7hx
Good looking out buddy. I updated the post.
Cooter
03-06-2018, 12:26 AM
I got the ZX-14 brake lever for the SX master and it needed the plunger pin hole deepened so it didn't depress the piston too far (aka old Buell issues) and the stop light switch pin was in the total wrong spot, drilled and tapped a 1/4"-20 shouldered bolt for a switch stop to make it work, but in my opinion, not at all a drop in replacement.
gdisaac07
03-06-2018, 12:33 AM
I got the ZX-14 brake lever for the SX master and it needed the plunger pin hole deepened so it didn't depress the piston too far (aka old Buell issues) and the stop light switch pin was in the total wrong spot, drilled and tapped a 1/4"-20 shouldered bolt for a switch stop to make it work, but in my opinion, not at all a drop in replacement.
You're correct. I also tried installing the ZX14 brake lever today and it did not work. Sorry for the bad info guys! Clutch lever works though.
Cooter
03-06-2018, 01:08 AM
It's closer than nothing if you've got the skills to change it.
My set-up is all on an '08 STT anyway. Modded ZX-14 aftermarket lever on an EBR radial 19mm master, Ducati Monster smoked reservoir, stock line and ZTL2 caliper. So for me, $29 and the mods were worth not spending $189 for ONE EBR lever... Yikes. What a kick ass upgrade to the XB!
Kid Thunder
03-07-2018, 12:06 AM
I ran the CRG ZX14 brake lever & it works fine. 7000 miles. The lever kit comes with different pieces for different bikes for the brake light. I think the one I used was fo a 600 Kawi. It's in the instructions. If not just give them a call & they will tell you.
gdisaac07
03-24-2018, 06:06 PM
I got the correct CRG RC2 lever. It is the one for the 2005 Kawasaki ZX-6R (Part # 2RN-511-T-B). I have installed it and confirmed that it's working as OEM.
@MakingPAIN, can you update the master list so that it reflects it?
gdisaac07
03-25-2018, 08:12 PM
This is a refactor of the OP. I'll update it as time goes on to be totally updated and help @MakingPAIN out.
The following is a constantly updated list of aftermarket parts vendors. If you have any more suggestions, please add a post with a manufacturer, part number, and link! The vendors are in alphabetical order per category, and some vendors are in more than one category.
OEM Parts Supply
EBR Parts Supply - http://www.erikbuellracing.net/store/
Updated chain slider (Part # G0012.1B7A)
LAP eBay page, Liquid Performance - https://www.ebay.com/sch/liquid_performance/
Aftermarket Dealers
AF1 (Our Forum Sponsor) - https://www.af1racingaustin.com/
NCCR (Official European EBR parts supplier, plus other aftermarket parts) - http://ebutik.nccr.se/ebr-erik-buell-racing-1/
St. Paul Harley Davidson - https://sphdonline.com/
Bodywork
Bestem USA
Carbon fiber replacement parts - http://www.bestemusa.com/1190-RX-SX_c_1930.html
Hotbodies Racing
Full race fiberglass bodywork - https://www.hotbodiesracing.com/product/1190rx-2014-15-race-bodywork/
PowerBronze
Seat cowl and tire hugger, 1190RX - http://www.powerbronze.co.uk/searchedproducts.aspx?maketext=EBR&modeltext=1190RX&yeartext=15
Seat cowl and tire hugger, 1190SX - http://www.powerbronze.co.uk/searchedproducts.aspx?maketext=EBR&modeltext=1190SX&yeartext=15
Screensforbikes.com
1190RX windscreen, short and tall - https://www.screensforbikes.com/shop/buell/erb-1190-rx-14/
Slingshot Racing
Keyless Billet Gas Cap - https://www.slingshotracing.net/catalog/buell-1125xb9xb12-ebr-1190rs1190rx-keyless-race-gas-fuel-cap-p-868.html
Twisted Designs
Tail Tidy Kit (Currently Out of Stock) - https://www.ebay.com/sch/twisteddesigns2016/m.html?_nkw=&_armrs=1&_ipg=&_from=
Seat
Stitch Wilson
Custom seats - http://customcycleseats.com/seats/custom-ebr-seats/
Rider Interface
ABM
Clutch Lever (Part # KH43) - https://ab-m.de/en/motorcycle-accessories-shop-details/125/brake-clutch-lever/5/lever-syntoevo
Brake Lever (Part # BH21) - https://ab-m.de/en/motorcycle-accessories-shop-details/125/brake-clutch-lever/5/lever-syntoevo
ASV
Clutch Lever (Part # CRC511 or CRF311) - https://asvinventions.com/dmsearch?q=CRC511+CRF311
Brake Lever (Part # BRC511 or BRF311) - https://asvinventions.com/dmsearch?q=BRC511+BRF311
CRG
Clutch Lever (RC2 for 2008 Kawasaki ZX-14, Part # 2RN-611-T-B, Shorty and other colors available too) - https://www.revzilla.com/motorcycle/crg-rc2-clutch-lever-kawasaki-zx14r-concours-14
Brake Lever (RC2 for 2005 Kawasaki ZX-6R, Part # 2RN-511-T-B, Shorty and other colors available too) - https://www.revzilla.com/motorcycle/crg-rc2-brake-lever-kawasaki-suzuki-triumph
Knight Design
1" drop foot pegs, black, Sidetrax tread for Buell Black Lightning (Part #101410-1110) - http://www.knightdesignllc.com/index.htm
Motion Pro
Adjustable throttle (Rev 2.1 Throttle tube, Part # 01-2778) - https://www.motionpro.com/c/rev2-throttle?v=10904
Vortex Racing
Pegs -
Woodcraft
Clip ons/bars (Part # 12-01 54mm) - https://www.woodcraft-cfm.com/cgi-bin/commerce.cgi?preadd=action&key=12-01
Solid foot pegs (Part # 04-BH1030Z) - https://www.woodcraft-cfm.com/cgi-bin/commerce.cgi?preadd=action&key=06-0300
Hand guards (Part # 15-010) - https://www.woodcraft-cfm.com/cgi-bin/commerce.cgi?preadd=action&key=15-010
Bar end sliders (Part # 16-9299B) - https://www.woodcraft-cfm.com/cgi-bin/commerce.cgi?preadd=action&key=16-9299B
Protection
GB Racing
Engine Case Protection - http://www.gbracing.eu/EBR.347/1190RX-%252526-1125.348/Engine-Protection.349/
R&G
Frame sliders, cooler grills, assorted tidbits - https://www.rg-racing.com/browseBike/EBR/
T-Rex
Frame sliders, engine sliders, axle slider - https://www.t-rex-racing.com/catalog.php?RideID=1608&RideDescr=Buell/EBR%201190RX%201190SX/2014%20-%202016
Techspec
Tank Pads (Part # 62-0020-SS) - http://techspec-usa.com/motorcycles/buell/buell-ebr-1190-ex-snake-skin-tank-grip-pads.html
Exhaust
APH
Exhaust - http://www.aph-performance-engineering.com/ebr_exhausts.html
Dean Adams
Round can, oval can, or exhaust tips, including or excluding ECU (either the one with the map exclusively for the type you buy, or a tunable ECU) - http://ecommerce.deanadamsdesigns.com/index.php?cPath=22
Various other tools - http://ecommerce.deanadamsdesigns.com/index.php?cPath=27
HMF
Exhaust - https://www.hmfracing.com/exhausts/buell/rx-1190
Continued:
gdisaac07
03-26-2018, 08:27 PM
Engine
Barnett
Clutch plates and springs (Part # 303-30-20125), required if you're using a new exhaust and putting down more power than stock) - http://www.barnettclutches.com/1368/buell/0/0/2009-buell-1125r.html
L.A. Sleeve
Upgraded cylinder sleeves - https://www.lasleeve.com/
NGK
Spark Plug (Part # CR9EKB) - https://www.amazon.com/NGK-CR9EKB-Standard-Spark-Plug/dp/B001RLS29W
Electronics
BUELLTooth
Quickshifter, regular shift or GP shift pattern - https://www.buelltooth.com/quickshifters.html
IDS
Original designer of the ECU, sells ECU's with other tunes, plus a user-tunable one - http://idspd.com/xcart/products-ebr
Shorai
OEM Lithium Battery (Part # LFX21A7-BS17, you must call Shorai directly to purchase one) - https://www.shoraidirect.com/en/c41-batteries
Battery Charger (Part # SHO-BMS01) - https://www.shoraidirect.com/en/p216219-lfx-battery-charger-maintainer-with-balancing-bms01-us-jp-power-cord
Battery Cable - https://www.shoraidirect.com/en/p140-bms01-spare-cable-set-12v
Woodcraft
Ignition bypass (Part # 43-0810) - https://www.woodcraft-cfm.com/cgi-bin/commerce.cgi?preadd=action&key=43-0810
Sprockets
JT Sprocket
Steel, 43 tooth, Part # JTR1490.43 - https://www.amazon.com/JT-Sprockets-JTR1490-40-Steel-Sprocket/dp/B001AVS70I?th=1
Steel, 44 tooth, Part # JTR1490.44 - https://www.amazon.com/JT-Sprockets-JTR1490-40-Steel-Sprocket/dp/B000GTYHVS?th=1
Supersprox
Steel/Aluminum engineered sprockets - https://www.supersproxusa.com/products.php?cat=1125906
Vortex Racing
Aluminum, 43 tooth, Part # Vortex-821-43 - https://www.amazon.com/Vortex-823-43-43-Tooth-530-Pitch-Sprocket/dp/B003170ASQ
Aluminum, 44 tooth, Part # Vortex-821-44 - http://store.58cycle.com/2Vortex_PN_821_44_Rear_Sprocket_Silver_p/2vortex%20pn%20821-44.htm
Suspension
Öhlins
Front Fork Cartridge Kit (Call Seacoast Sport Cycle for NIX30 kit, installed for $1,750 + Shipping) - http://seacoastsport.com/
Rear Shock (Part # BU-888 is the 1125/RS rear shock, a drop-in part to the 1190RX/SX. A note though: these were all built in 2011 or earlier. If you purchase one, you'll have to have it serviced/rebuilt before you fit it to your bike or the seals may fail very quickly) - https://www.ebay.com/itm/Ohlins-TTX36-REAR-SHOCK-Ohlins-Advanced-Suspension-Technology/202230827159
Steering Damper (Part # SD000, requires bushing kit Part # A14010200UX0631) - https://www.amazon.com/Ohlins-SD-000-Steering-Damper/dp/B0067F630I
Showa
Stock Big Piston Forks and Shock -
Race Shock - https://www.amazon.com/Buell-Erik-Racing-Motorcycle-SHOWA/dp/B077DNQHLD/
Wilbers
Race Shock - http://ebutik.nccr.se/ebr-erik-buell-racing-1/ebr-suspension/nightline-all-black-ebr-1190-rx-sx-wilbers-adjustline-632-mono-c
Brakes
Diesel Moto
Front Rotor -
EBC
Brake Pads -
SBS
Dual Sinter Front Brake Pads (Part # 856DS) -
Wave Rotor
Front Rotor, Part # BL02FID
Fluids and Filters
YOU MUST USE 10W-40 SYNTHETIC ENGINE OIL IF YOU PLAN ON RIDING AT ANY TIME WHEN IT IS LESS THAN 40 DEGREES FAHRENHEIT. OTHERWISE, USE 20W-50 SYNTHETIC.
AMSOIL (EBR recommends that you use AMSOIL)
10W-40 Oil (Part # MCF+QT-EA) -
20W-50 Oil (Part # MCVQT-EA) -
HIFLO
Oil Filter (Part # ) -
K&N
Oil Filter (Part # KN-564) -
K&P Engineering
Metal mesh oil filter (Part # ) - http://kandpengineering.com/product-catalog/s27/
McMaster-Carr
M18 Oil Drain Plug LH Washer - Equivalent to EBCF0092.1B6 - https://www.mcmaster.com/#97725a860/=1bnm6de
M12 Oil Drain Plug RH Washer - Equivalent to EBCF0091.1B6 - https://www.mcmaster.com/#97725a250/=1bnm6vb
Oil Filter Cover O-Ring - Equivalent to EBCF0003.1B6 - https://www.mcmaster.com/#9452k147/=1bnm7hx
Mobil 1
10W-40 Oil -
20W-50 Oil -
Royal Purple
10W-40 Oil -
20W-50 Oil -
Spools/Stands/Restraints
Driven Racing
Spools -
Pit Bull
Spools (6mm, Delrin only) -
Rear pit stand (Wide stand) -
Front pit headlift stand (Pin #1) -
Trailer Restraint System (Part # ) -
I will try to keep the list up to date. Please help out with it if you can. If there are any links that are broken, please let me know and try to provide a new, working link. Thank you!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.