Page 5 of 5 FirstFirst ... 345
Results 41 to 44 of 44

Thread: Loss of Communication on Display

  1. #41
    EBRforum ProvNov
    Join Date
    Aug 2015
    Location
    modesto, ca
    Posts
    35
    Any new and improved options for correcting the Comm Error? I got my first one a few days back, 2014 SX #168, 2000 miles. Bike ran fine to the coffee shop and then died on restart about 45 minutes later. Followed by four or five start attempts with no fire. Dash flashed the Comm error and Said Low Fuel pressure once. About the sixth start attempt, it fired up and I headed strait for home, idle was a little rough so I kept the RPM's up at intersections but it died once anyway but restarted fine. With my house in sight, I was able to run it up to near full power for a gear or two to see if WOT was affected, seemed pretty good. Coincidentally all this on it's first ride out with a new APH dual exit exhaust and matching IDS 44-tooth ECM. I hate it when an issue surfaces just after a parts swap, so I know that swapping back to the factory ECM to see if the issue continues is next in the troubleshooting list of things to do. Dash and original ECM were shipped out to LAP/EBR for the Dash update earlier and ran a few tanks since then. I pulled the dash out for inspection for cold/stressed solder joints and to Pott all the connectors as suggested in previous posts. Upon disassembly, I see that mine has already been Potted at all the suggested places so can't (without razor knifing the Potting material) pull the circuit board up/off to inspect for cracked circuit traces and the like. Email has been sent off to EBR for the official $$$ repair option..
    My apologies for this post being in two threads, the first one looked appropriate but I saw this one and felt it was more specific
    mike

  2. #42
    EBRforum Newb
    Join Date
    May 2017
    Location
    Northern California
    Posts
    27
    Would be more suspect if the new ECM causing the problem.

  3. #43
    EBRforum ProvNov
    Join Date
    Aug 2015
    Location
    modesto, ca
    Posts
    35
    Update....
    Upon inspection of the Dash, I find that it has already been Potted and EBR tells me that based on it's serial number it is not the original one for my bike. Also told me it is one of the later, improved ones that are "post" "Comm Error". I contacted the Dealer that I purchased the bike from about any repair history on it prior to it being sold to me as the first owner. They said that other than a first 600 mile service, there were no other issues or services performed on the bike. It was their Demo bike when I purchased it new with just over 600 miles on it. The only time I had the Dash out was for the Free Dash and ECM Firmware upgrade about last year. EBR said they didn't switch it out, so it's a mystery how I ended up with a later model dash. Back to the troubleshooting..
    After clearing all the faults, I re installed the original ECM and the bike still had an intermittent fuel system fault that continued to get worse. I noticed that it also showed a zillion other faults after swapping the ECM. I cleared them all and put the APH IDS ECM back in to continue with trouble shooting. Upon swapping the ECM, I got more Faults, including the Comm. I cleared them all to start fresh and was only getting Fuel System Faults from then on. The fuel pump issue progressed to a completely non-working fuel pump while tinkering in the garage for bad grounds, chaffed harnesses etc. Working backwards from the pump to the wiring on the harness to see where things were changing from good to bad electrically, I found that the four pin Weather-Pac looking Fuel pump connector, to the main bike harness, one of the connection had a bad female contact on the Pump ground wire. There are little spring loaded wiper strips inside the female contact that keep good pressure and contact to the male pins. The "wiper" was completely pushed back out of the way and was not making contact with the male pin when assembled. I tweeked the wiper back to the center of the contact and reassembled the plug. The bike started instantly. I re-assembled everything and four short separate (close to home) test drive trips totaling about 150 miles finds everything working perfectly, no faults and the bike runs like a scalded cat. So, so far, I think my Comm fault may have been just from swapping out ECM's within seconds of turning off the key and the Dash hadn't internally gone fully off like it would if you let it sit key off for a half an hour and then swapped parts. As for my bike having an updated Dash that supposedly wasn't even made when I bought it? Who knows, The EBR guys say that they would have sent my original one back that I sent in for update so the mystery goes unsolved. Hopefully with the newer Dash, the Comm issue will never return to haunt me...
    Happy mike...

  4. #44
    EBRforum Newb Lorne's Avatar
    Join Date
    Mar 2018
    Location
    Australia
    Posts
    11
    I got Communication error and the instant it appeared the engine stopped. I pulled in the clutch pulled over turned off the bike turned it back on all looked good looked at diagnostic no issue or history. Started the bike got up to 3rd gear it happened again I pulled in the clutch error disappeared let the clutch out and high sided Broke my Fibula. 2014 bike but only got it new at Xmas it has 2500 km on it.:-(

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •